Silencing Frigidaire mini in-window compact room Air Conditioner Model FAA065P7A

Instructions on Silencing Frigidaire Mini In-Window Compact Room Air Conditioner Model FAA065P7A – 6000 BTU MSII

If you look at reviews for this otherwise nice, small A/C unit, you’ll see lots of people complaining about a loud beep every time you press a button on the unit or the remote (e.g. changing fan speed or temperature). It’s a high pitched, noisy, piercing, annoyingly loud beep, which wakes spouses and babies. I know of no way to disable or turn off this “feature”. I looked for a wiring diagram and didn’t find anything promising, so I decided to slightly disassemble the unit and hope to find a speaker. I wound up fixing it and here’s how you can as well!:

Tools required:

  • Phillips screwdriver
  • Flathead screwdriver
  • Glue (I used a glue stick)

Time required: about 10-15 minutes

Skills required: Basic Handyman. Having said that, here’s my disclaimer: Only skilled, certified electricians should attempt to fix electronic equipment. These units may contain capacitors which hold electric charge. Do not touch any of the electronics. I am absolutely not responsible for loss of property or person, damage to this unit or your cat, accuracy of these instructions, nor do I guarantee that this will even work. Opening this unit may void the warranty.


  2. Swing open the front vent like you’re going to change/clean the filter and then gently and slowly swing open further to pop the two bottom hinges until it comes off. Set it and the filter aside.

    ( First swing open, then remove vent )

  3. Remove 3 large screws and set aside (be careful not to brush anything up against the fragile aluminum vents).

    ( Location of the 3 screws to be removed for removal of outer plastic ring )

  4. Remove 4 (there may only be 3) small screws around the control panel and set aside.

    ( Location of the 3 (or 4) small screws needed to remove the control panel )

  5. Pop off the outer plastic front piece which has the top vents attached. Do this by gently inserting a flathead screwdriver from the inside into the slot about half-way down on the right side until that side comes off. Repeat for the left side. Then, the trick is to try and gently pull this outer plastic piece up (there are two tabs along the top like there were on each side). Be careful as there is a wire which attaches this piece to the rest of the unit, so orient it so that you don’t put any tension on this wire.

    ( From along the inside, press tab with screwdriver to assist in removal of outer plastic ring )

    plastic ring removed

    ( Set plastic ring gently aside -- there's a wire connected to it )

  6. Remove 3 screws (there may only be 2) which were behind the control panel and set aside.

    ( 2 (or 3) screws to remove from electronics plate )

  7. Lift slightly (there are two hooks along the right edge) and carefully pull out this plate with attached electronics only far enough so that you can see and can just access to the small, black cylinder (about the size of an Altoid mint). This is the PCB mounted speaker.
    Top view of Speaker

    ( View of the hole to plug with glue (looking down) )

  8. Take your glue and make a small (about the size of a grain of rice) ball and place on the end of your flathead screwdriver.
  9. Carefully use the screwdriver to apply the glue ball to fill the hole which is at the center of this piece (don’t get glue on anything else). Be sure to pack enough in the hole to muffle the sound (about 2 grains of rice worth). You can also use an unfolded paperclip to help push the glue inside the hole and to damage the diaphragm which makes the noise.
  10. Now, carefully reassemble the unit in the reverse order.


  • I would not test your success until you have at least the two electronic panels securely screwed back into place.
  • For my three attempts at this, one now makes no beep, one left the beep barely audible and the other reduced the volume by half.
  • I did all this while my units were installed in windows.
  • If not obvious, this is basically irreversible.
  • This also works on model # FAA055P7A and may work on these model #s: FAA084P7A, FAC124P1A, FAA086P7A, FAA064P7A and FAC104P1A.

Good Luck!

11 thoughts on “Silencing Frigidaire mini in-window compact room Air Conditioner Model FAA065P7A

  1. If I’m not mistaken, the little speaker has a diaphragm at the base of the unit inside the hole. So, the problem with the ‘cover it up’ approach is that it will only slightly muffle the sound. You can try it, then let us know how it works!

  2. Thankyou!
    I have a fault in the control panel that makes it occasionally (at random) change turn on and off the timer.
    usually at 3:00 am.

    Now I have silence instead of some insane beeping.

  3. erm. Should note that instead of using the glue, when I tried to poke the hole in the diaphram, the top of the beeper (labeled buzzer on the circuit board) came off. This left just the two contacts that used to connect to the diaphram.

    Now if I could fix the other boards issue… but still, better to have it act oddly on occasion than to act oddly and wake me up.


    Similar technique worked on Kenmore 253.70051 (also made by Fridgidaire). Drilled a _small_ hole in the side of the buzzer to allow air to escape and filled it with silicone caulk (until it came out the drilled hole). Now a civilized volume.

  5. Shoving something in the PSO buzzer did not work for me. My dog was terrified of this unit. It’s a GE 6000 BTU model AEL 06LV. Finally, I reluctantly took needle nose pliers and pull the top of the buzzer off revealing to metal wires that touched each other. All I did was take the needle nose and bend them apart and put the cap back on. No more buzzer, but dog still won’t come in! Ha ha Ha

Leave a Reply to Todd Cancel reply

Your email address will not be published. Required fields are marked *